Jiaozuo brake

Special electric hydraulic brake for steel mills

Installation, commissioning and maintenance of electric hydraulic brakes:

1. Installation

The brake is installed on the machine after the brake wheel is installed. The brake wheel must be dynamically and statically balanced, with a surface roughness of not less than Ra l. 6 and a hardness of not less than HB=280. When installing and fixing the brake, attention should be paid to whether the brake shoe is parallel to the brake wheel when the brake is released; In the braking state, the brake pads should stick to the brake wheels. The non parallelism and inclination in the released state shall not exceed 0.1mm within the width of the brake wheel of 100mm. The working surface of the brake wheel must not have oil stains.

2. Oil injection

Before the test run of the electric hydraulic thruster, clean and free of any dirt and mechanical impurities hydraulic oil must be injected into the cylinder. Connect the hydraulic power supply and check if the impeller rotates flexibly, if the circular spring is stuck, and if the push rod and piston move up and down without any jamming.

3. Adjustment of braking torque

By adjusting the adjusting nut of the main spring and changing the compression length of the spring, the spring force and braking torque can be adjusted to ensure that the brake operates with as little braking torque as possible.

4. Adjustment of the brake pad setback of the brake

Due to the brake's ability to automatically adjust clearance, as the brake pads wear, the clearance between the left brake pad and the brake pad can always remain unchanged, but the clearance between the right brake pad and the brake pad gradually increases with the wear of the brake pads. It is necessary to adjust it in a timely manner according to the situation to ensure that the distance between the two brake pads is basically uniform.

5. Stroke adjustment of the thruster

The smaller the working stroke of the electric hydraulic thruster, the more ideal it is to ensure that the brake shoe has less backlash. Therefore, it is necessary to adjust the height of the electric hydraulic thruster.

Multiple disc drum brakes

6. Inspection of brakes

The braking device should be regularly inspected. If used to start the equipment, the brake of the overweight mechanism should be inspected once per shift, and the motion mechanism should be inspected once every three days. Emphasis should be placed on checking whether there is any jamming at the hinge joint; Whether the brake components move normally: whether the electric hydraulic thruster moves normally; Whether there is any oil leakage or seepage phenomenon; Is the installation height of the thruster appropriate; Is the brake shoe correctly pressed against the brake wheel; Is the condition of the friction surface intact and free of oil and dirt.

Widely used in steel, lifting, metallurgy, mining, ports, construction, and electricity, Main products in hydraulic machinery include: electric hydraulic block brake series YWZB YWZ3B YWZ4B YWZ5 YWZ8 YWZ9 YWZ12 YWZ13 YW YWL TYWZ2 YWP electromagnetic block brake JZ (TJ2A) MW (Z) ZWZA ZWZ2 ZWZ3A DCW3 electromagnetic failure protection disc brake 5SE 561SE 560SE 56SE DCPZ12.7 4SE 3SE ST1SE ST2SE 450SE hydraulic failure protection disc brake 5SH 4SH 3SH 450SH ST1SH ST2SH SH ST3SH ST4SH SB (YQP) SBDST5SH ST10SH ST16SH ST25SH ST25SH-A ST40SH 904SH SBB electric hydraulic arm disc brake YPZ2 Ⅰ, Ⅱ, Ⅲ YPZ2 Ⅳ, Ⅴ, Ⅵ pneumatic caliper disc brake QP12.7 5SP 4SP 3SP 450SP PD ADP60M-ADP61M-ADP62M hydraulic direct acting disc brake DADH75 ADH60 ADH90 ADH120 DADH80 DADH90 DADH120 DADH103 DADH195 electric hydraulic thruster YT1 Ed