Jiaozuo brake

Product Introduction:

Brakes:

Electric hydraulic brake, electric hydraulic drum brake, electromagnetic block brake, electric hydraulic windproof iron wedge brake

Safety wind brake electromagnetic failure protection disc brake electric hydraulic arm disc brake wind electric yaw brake

Wind power spindle brake Pneumatic caliper disc brake Hydraulic failure protection caliper disc brake Electromagnetic failure protection brake

Hydraulic direct acting disc brake electromagnetic caliper disc brake pneumatic failure protection brake hydraulic direct acting brake

Motor disc brake

Pusher:

Electric hydraulic thruster explosion-proof electric hydraulic thruster

Brake pads:

1. Ordinary materials (resistant to high temperature of 400 degrees)

2. High wear-resistant materials (4-8 times the service life of ordinary materials)

3. Special wear-resistant material (8-12 times the service life of ordinary materials)

4. Explosion proof materials

5. Copper based material (resistant to high temperature of 800 degrees)

6. Anticorrosive materials

Non standard products:

1. YQP series: YQP50 YQP100 YQP160 YQP250 YQP315 YQP400 YQP365

2. SB series: SB50 SB100 SB160 SB250 SB365

3. YPZ series: YPZ2-I YPZ2-II YPZ2-III YPZ2-IV YPZ2-V YPZ2-VI P2-III

4. QP series: QP12.7 QPL12.7-A QP25.4 QP30 QP40

5. YP series: YP1 YP2 YP3 YP11 YP21 YP31 YP41

6. Yaw series: (0.8 MW, 1.5 MW, 2 MW) DADH75 DADH80 DADH90 DADH103 DADH120 DADH195

7. ADP series: ADP (H) 60 ADP (H) 90 ADP (H) 120

8. SE series: 3SE (P) 4SE (P) 5SE (P) 450SE 56SE

9. ST series: ST1SH ST2SH ST3SH ST4SH ST5SH ST10SH ST25SH ST25SH-A ST40SH ST3SH-A

10. Wheel edge: YLBZ25-160 YLBZ40-160 YLBZ40-180 YLBZ40-200 YLBZ40-150 YLBZ63-180 YLBZ63-200

YLBZ63-210 YLBZ100-200

11. Copper based: FSH30 BSFA70 HB30

12. Drilling rig: BSC90 ZWPS65-1

13. Wind power high-speed shaft: (0.8 MW, 1.5 MW, 2 MW)

According to your needs, choose temperature resistance, wear resistance, select materials, provide drawings, or provide technical requirements to design friction coefficients according to production requirements.

The braking force is generated by a set of disc springs that apply force to two friction plates through transmission.

When the released energy disappears or a mechanical system malfunction is found,

The release of energy in balance between brake action and braking force is achieved by

Generation: electric SE series hydraulic SH series pneumatic SP series 2 kinds of fail safe disc brakes

A: Working brake, allowing high-frequency braking. High braking force, low maintenance costs, automatic repair of worn pads

Compensation device with short response time. Large installation tolerance: brake disc end face runout, large value

0.2mm

. The verticality deviation of the base relative to the disc, with a maximum value of 4% o. Large deviation of Centre-to-centre distance of brake disc relative to base

2.5mm. This series includes the following types of brakes:

561SE 560SE 56SE 5SE 450SE 4SE 3SE brakes. Electromagnetic release. An ESE/ESP electronic control box is required for operation. 5SH 450SH 4SH 3SH 904SH brake. Hydraulic release. A hydraulic station is required for operation.

5SP 450SP 4SP 3SP brake. Pneumatic release. B: Maintain and emergency brakes: With high braking force, just like various brakes. In case of overspeed detection, use

As an emergency brake, the response time of the static brake is short under normal circumstances. Manual adjustment device with pad wear.

Large installation tolerance:

Brake disc end face runout: maximum 0.2mm. The verticality deviation of the base relative to the disk is 4%. Installation dimensions: refer to the data sheet.

This series includes a series of types of brakes:

All SE series. Electromagnetic release. Equipped with electronic control box ESE/ESP during operation

. All SH series are mainly ST series. Hydraulic release. Equipped with a hydraulic station during operation. All SP series. Pneumatic release.

Direct acting brake:

The braking force is generated by the following methods: hydraulic or pneumatic current hydraulic ADH series pneumatic ADP series electric ADE series uses a pressure control device to adjust and control the corresponding pressure to generate braking force to meet the usage requirements.

Some brakes can be equipped with an automatic adjustment device for pad wear and a pad reset system.

Brake pad:

The brake pad is asbestos free:

M-type gaskets are used for dynamic and high-speed applications. Type A gaskets are used for static or very low speeds.

Other:

According to different user requirements, the following devices can be installed:

Pad wear display, brake display, manual release display.